Guide Jun 26, 2026 7 min read By Marcus Elite

Maserati Rear-End Clunk: How to Tell Which Control Arm Is Actually Failing

There's a clunk from the back of your Maserati every time you cross a speed bump or a broken patch of road. The rear end feels slightly vague, the steering wanders a touch on the motorway, and your rear tyres are wearing unevenly. The cause is almost always a worn rear control arm — but the Ghibli, Quattroporte, and Levante have several rear arms, and the real question is which one.

Most articles stop at "replace your control arm," which is useless when there are multiple arms back there doing different jobs. This guide breaks down the rear suspension by function so you can identify the failing component, confirm it, and order the correct genuine part the first time.

How the rear suspension is laid out

These Maseratis use a multi-link rear suspension, where several separate arms each control one aspect of wheel movement. Some manage toe (which way the wheel points), some manage camber and lateral location, and some handle fore-aft loads. Each arm pivots on bushings and ball joints. Because they share the load, a single worn arm produces noise and imprecision out of proportion to its size — and replacing the wrong one fixes nothing.

The three arms to know

Across these platforms, three arms account for the overwhelming majority of rear clunk complaints. Knowing what each does tells you what its failure feels like.

Rear toe link / adjustment rod — Levante, part 670032017. This is the arm that sets rear toe, and it's also the one used to dial in alignment. When its bushings wear, toe drifts under load — meaning the wheel points slightly differently when you accelerate, brake, or load the chassis in a corner. The result is a rear-end clunk, a wandering feel on the motorway, and rapid, uneven tyre wear. If you're burning through rear tyres faster than fronts, look here first.

Rear upper tension bar / control arm — Levante, part 670032016. This arm locates the upper rear geometry, controlling camber and lateral position at the top of the upright. Wear here brings knocking over bumps and a loose, imprecise rear feel — the car no longer tracks cleanly through quick direction changes. It's typically a lighter, higher-pitched knock than the lower arms produce.

Rear lower fork / track control arm — Ghibli & Quattroporte, part 670002808. This is a major lower locating arm on the saloons. Because it carries significant load and sits low in the assembly, worn bushings here produce a heavier, deeper clunk over bumps and a noticeable drop in rear stability. When a Ghibli or Quattroporte owner describes a solid "thunk" rather than a rattle, this arm is the usual suspect.

Why they fail

The arms themselves are robust. They're forged or cast metal and they rarely bend or crack unless you've had a serious impact. What fails are the wear items built into them: the rubber bushings and the ball joints.

Rubber bushings live a hard life. They're squeezed, twisted, and heated thousands of times on every drive, and they sit close to hot brakes and exhaust components. Over years, the rubber perishes — it dries out, cracks, and loses the elasticity that lets it absorb movement while still locating the arm precisely. Once that happens, the bushing develops play, and the arm starts moving when it shouldn't. Ball joints follow a similar path: the grease degrades, the joint wears, and free play creeps in.

Driving conditions accelerate everything. Potholes, kerb strikes, aggressive speed bumps, and sustained spirited driving all hammer the bushings. Hot climates are particularly hard on rubber — relevant if you're running the car in the Gulf, where heat ages bushings faster than in temperate markets. Once any joint has play, the metallic clunk and the alignment drift are not far behind.

The symptoms owners report

Clunk or knock from the rear over bumps, speed humps, and rough roads
Vague, loose rear end that feels like it "steers" slightly on its own
Uneven or rapid rear tyre wear (a hallmark of toe-link wear)
Alignment that won't hold settings, or pulls after a short time
Clonk when transitioning from acceleration to braking

How to confirm which arm

Symptoms narrow it down; a proper inspection confirms it. Don't order parts on a guess — these arms aren't cheap, and the diagnosis is straightforward for a competent technician.

Inspect the bushings on a lift. With the car raised, a technician levers each arm in turn with a pry bar, watching and feeling for the joint that moves. The arm whose bushing flexes or knocks under that load is your culprit. This is the single most reliable test and takes only a few minutes per arm.

Read the tyre wear. Feathered tread or wear concentrated on the inner edge of the rear tyres points strongly at the toe link. Toe controls how the tyre scrubs across the road, so toe drift shows up as a distinctive wear pattern long before anything else fails.

Locate the noise by character. The lower fork arm produces a heavier, deeper clunk you feel through the floor. Upper-link wear is a lighter, sharper knock. Where the sound sits — and how it feels — helps separate upper from lower before the car even goes on the ramp.

Check the alignment history. An alignment that won't stay put is a classic worn-arm signature. If a shop set the car correctly and it drifted within weeks, a bushing is letting the geometry move. Fresh alignments don't wander on healthy suspension.

Affected models and part numbers

Arm	Model	OEM Part
Rear toe link / adjustment rod	Levante (M161)	670032017
Rear upper tension bar	Levante (M161)	670032016
Rear lower fork / track arm	Ghibli & Quattroporte	670002808

Rear arms are side-specific and model-specific, so confirm fitment against your VIN before ordering. Send us your chassis number and we'll match the exact arm.

The genuine fix and what it costs

The repair is replacing the worn arm (sold as left-and-right sets where applicable) and then performing a four-wheel alignment, since any rear-arm replacement changes geometry. Replacing arms in pairs gives even, predictable handling and avoids a fresh bushing working against an old one. We stock the relevant genuine arms: the Levante rear toe link (670032017), the Levante rear upper tension bar set (670032016), and the Ghibli & Quattroporte rear lower fork arm (670002808), shipping from our UAE and USA warehouses.

What happens if you ignore it

A rear clunk is easy to live with for a while, and that's exactly the trap. Worn arms don't just rattle — they let rear geometry drift continuously. That drift chews through tyres and undermines stability precisely when you need it most: fast direction changes, motorway lane shifts, and wet roads where a loose rear is genuinely dangerous.

There's a compounding cost, too. A joint with play transfers extra load into the adjacent bushings and joints, wearing them prematurely. What starts as one failed arm becomes two or three if left long enough. Catching it early keeps the repair to a single component and protects a set of expensive tyres that worn toe will otherwise destroy.

A rear clunk on a Ghibli, Quattroporte, or Levante is a worn arm — the trick is identifying which one. Pinpoint the joint with play, fit the correct genuine arm, align the car, and the rear end feels tight again.