BMW X5 X6 Engine Mount Set Left Right Genuine 22116778191, 22116778192

Replacing both engine mounts together is not just recommended—it's mechanically essential for several critical reasons: Engine positioning: Your BMW's engine is suspended between two mounts. Both mounts work together to maintain precise engine positioning within the engine bay. If only one mount is replaced: (1) Asymmetric support—new mount on one side, collapsed mount on other creates uneven engine positioning affecting drivetrain alignment, (2) Uneven vibration isolation—new mount absorbs vibration correctly, old mount transmits vibration unevenly creating new irregular vibration patterns, (3) Accelerated wear—new mount compensates for failed mount, bearing excess load and wearing prematurely (potentially failing in 20,000-30,000 miles rather than 100,000+), (4) Drivetrain stress—misaligned engine position stresses driveshaft, transmission mounts, and CV joints. Financial logic: Replacing one mount now, then other fails in 6-12 months = two labor charges + two parts purchases. Replacing both simultaneously = one labor charge + both parts. Labor consideration: Engine mount replacement requires raising and supporting the engine—doing both sides in one operation adds minimal extra time (30-60 additional minutes) but eliminates need for complete second service. BMW engineer design intent: These mounts are designed as a system working in concert. Always replace as complete set.

BMW X5/X6 engine mounts are typically hydraulic (fluid-filled) mounts rather than simple solid rubber units—and this distinction is critically important: Hydraulic mount construction: Contains fluid-filled chambers and internal valving that provide dynamic, variable damping characteristics. At idle, hydraulic mounts provide maximum isolation. During acceleration and load, internal valving stiffens the mount to control engine movement. Why this matters: (1) Hydraulic mounts cannot be substituted with simple rubber mounts—the dynamic damping characteristics are fundamental to X5/X6 NVH (Noise, Vibration, Harshness) engineering, (2) Genuine BMW hydraulic mounts are calibrated specifically for X5/X6 engine mass, torque characteristics, and chassis resonance frequencies, (3) Aftermarket hydraulic mounts often use different fluid viscosity or valve calibration, resulting in noticeable NVH differences from factory specification. Genuine BMW advantage: Factory-calibrated fluid viscosity and valve characteristics match exactly to BMW's NVH engineering for your specific engine. Signs of hydraulic mount failure: Fluid leaking from collapsed mount, complete loss of damping (mount feels solid), or conversely, excessive softness indicating internal valve failure. Important: Confirm with seller whether these specific part numbers are hydraulic or solid rubber mounts for your particular engine variant—some diesel and petrol engines may use different mount constructions.

Engine mount replacement on BMW X5/X6 models is considered advanced DIY or professional-level work due to specific requirements and risks: Why it's challenging: (1) Engine must be supported and lifted—requires engine support bar or engine crane to take weight off mounts during replacement; without proper support, removing a mount can cause engine to shift dangerously, (2) Access limitations—mounts are located under the engine with limited space; some engine accessories or components may require removal for access, (3) Torque specifications critical—all mounting hardware must be torqued to exact BMW specifications for safety and proper mount function, (4) Engine positioning—engine must be correctly positioned before final torquing to avoid drivetrain misalignment. Tools required: Engine support bar (BMW special tool or quality aftermarket equivalent), hydraulic floor jack, jack stands, torque wrench, metric socket set, BMW-specific torque specifications. Professional installation advantages: (1) Access to proper BMW engine support tools, (2) Experience with X5/X6 specific access challenges, (3) Ability to inspect related components (transmission mount, subframe mounts) while disassembled, (4) Warranty protection through professional installation. Average professional labor: 2-3 hours for both mounts. Recommendation: Unless you have professional-level mechanical experience and proper engine support tools, professional installation is strongly advised for this safety-critical drivetrain component.

Yes, we ship to most countries worldwide.

You can track your order directly through our website by following these steps:

1. Go to the Europarts360 Tracking Page.
2. You will see an option to search by Tracking Number or Order ID.
3. Enter your number in the search bar.
4. Click the "Track" button to view the current status of your shipment.

We offer a 14-day return policy for all unused items in original packaging.

This warranty covers all eligible products purchased through our website for 6 months from the date of purchase.